01 The problem underground
Buried utilities sit inches apart, and a bucket can't feel them. Under most city streets runs a crowded maze of gas lines, fiber, water mains, power cables, and sewers.
Hit one with steel teeth, and you can get an outage, a fire, or worse.
The Common Ground Alliance estimates the damage costs the U.S. about $83 billion a year.
So how do you dig right next to them? Swap the steel for water and air.
02 The core idea
Here's the core idea: two systems at once. It's called hydro excavation, or hydrovac, and it's what our crews at NG Companies do every day.
A high-pressure water jet does the cutting, turning the soil into a thick mud called slurry.
At the same time, a powerful vacuum lifts the slurry up a wide hose into a sealed tank on the truck.
No blade or bucket ever touches the pipe. That's the whole safety case.
03 Anatomy of a hydrovac
Let's walk around the truck: six systems on one chassis. Along the frame ride the water tanks, holding from a few hundred to about 1,500 gallons.
Next to them is the high-pressure pump, which feeds the hand-held digging wand.
Many trucks add a diesel-fired heater for frozen ground and dense clay.
At the rear, the sealed debris tank holds what the hose picks up, typically 5 to 15 cubic yards.
Then there's the vacuum blower, the heart of the machine. It creates the suction.
And a hydraulic boom swings the suction hose over the dig, 20 feet or more from the truck.
04 The water side
Start with the water: cutting power, not volume. The pump runs at 2,000 to 3,000 psi, versus about 40 to 60 at a household tap.
But the flow stays modest, often 10 gallons a minute or less, so the jet cuts without flooding the hole.
Operators favor a rotating nozzle, which sweeps the jet into a cone instead of a single needle.
The rules are simple: keep the tip moving, hold it at least 8 inches from any utility, and never jab the nozzle into the ground.
05 The vacuum side
Now, the vacuum, where the atmosphere does the pushing. The blower pulls air out of the sealed debris tank, dropping the pressure inside well below the air outside.
Outside air rushes in through the only opening, the end of the hose, and carries the slurry with it.
The first number to know is airflow: how much air moves, often 2,500 to 6,000 cubic feet per minute.
The second is vacuum depth, in inches of mercury: how hard it pulls. Perfect vacuum is about 30 inches at sea level, and a positive displacement blower can reach around 27, roughly 90%.
Fan systems move lots of air, but top out around 16 inches, so they fade on deep holes and long hose runs. Positive displacement blowers keep pulling.
06 Inside the debris tank
The debris tank is a big, slow room for air. The fast airstream from the hose slows down in that open space, and rock, soil, and water drop out.
Then come the guards. First, if the tank overfills, a float ball rises and seals the outlet.
A backup shutoff catches what slips past, and filters or cyclones strip out the fine dust.
Only clean air reaches the blower, and it leaves through a silencer that quiets the exhaust.
When the tank is full, the rear door opens and the body tilts, dumping the load at an approved site.
07 Hot water, frozen ground
Hot water makes hydrovac a year-round tool. A large onboard heater can push water to around 175 degrees Fahrenheit.
For frozen ground, crews typically run 140 to 180 degrees. That's how we keep digging through a Denver or Boise winter.
Close to the line itself, crews dial it back. One gas-industry guideline caps water at 115 degrees and 2,500 psi.
08 Where hydrovac earns its keep
Hydrovac earns its keep from test holes to tree roots. The most common job is potholing, or daylighting, a small test hole that shows a line's exact depth and position before anyone bores nearby.
Here's the catch: 811 gets utilities to mark their own lines, but usually only up to the meter, so private lines past it aren't marked.
So we pair hydrovac with private locating through our partner, Safe Site. Ground-penetrating radar and electromagnetic locators find the lines, and the hydrovac exposes them.
Beyond potholing, hydrovac cuts slot trenches, digs pole and pile holes, cleans out valve boxes, and works around tree roots.
Why water and not air? Air excavation needs no water and leaves dry soil you can reuse, but hydro is generally faster, and handles clay and frozen ground better.
09 Disposal and safety
Wet slurry and a powerful jet both need a plan. Raw slurry can be around 60% water. It goes to an approved site to be separated, tested, and landfilled or recycled, never down a storm drain.
Good process still comes first: call 811 before digging, chock the wheels, work in teams of at least two, and wear eye, face, and hearing protection. The jet can pierce skin, so it's never pointed at anyone.
10 Why NG Companies
Why NG Companies? National reach, with local crews. Damage prevention is what we do, with crews in Nashville, Dallas–Fort Worth, Tampa, Charlotte, Boise, and Denver.
One call gets you all five of our services: hydrovac, utility locating, video pipe inspection, hydro jetting, and trenchless pipe repair.
We've potholed and excavated for a downtown Kansas City water main replacement, and handled complex excavation for Tampa International Airport's new terminal.
Large contractor or small, you get the same commitment and the same grit, in every market from healthcare to heavy civil.
11 Recap
So that's hydrovac: a hole dug exactly where you need it, with the buried lines around it still intact.
Water cuts the soil. Air lifts it away. The tank separates the heavy material. And the guards protect the blower.
Ready to solve what's below? Call NG Companies at 844-642-8227, or visit ngcompanies.com. Dig with confidence.